jims

Jims #: 1010 The piston pin align tool is used to check straightness of the rod without removing rods from case. Tool is 4-1/2 inch long. Fitment: ...

Jims #: 1164 The Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed...

Jims #: 2315 The Jims primary locking tool is used to lock the clutch hub sprocket to the front engine sprocket. It also allows the removal or torq...

Jims #: 2122A Receptacle extractor tool removes Molex style connector Fitment: 0 All

Jims #: 24587-39 · OEM #: 24587-39, 413-39AC .005 oversize right side case race is machined and ground to factory specifications. Fitment: 1939-19...

Jims #: 95760-57 · OEM #: 95760-57 This rocker arm roller bearing puller Fitment: 0 All Installation instructions (PDF)

Jims #: 94804-57 · OEM #: 94804-57 The Jims rocker arm bushing reamer tool is used to ream rocker bushings to a factory fit of.0007 inch-.0012 inch...

Jims #: 17611-66B · OEM #: 17611-66B Jims rocker arm shaft has an outer diameter at the big end of.937 inch and the small end of.434 inch. Measurem...

Jims #: 975 This Jims shaft turning tool fits spline or taper on assembled motor and allows engine to be turned over by 1/2 inch ratchet or impact ...

Jims #: 937 Shoulderless valve guide drive tool handle only will remove shoulderless valve guides including the 7mm size guides. Use driver handle ...

Jims #: 938 This valve guide installer takes the guess work out of valve guide installation while insuring that the valve guides are installed to p...

Jims #: 1710 Snap ring remover tool will remove the Timken bearing outer race snap ring without damage to the case. You can replace the snap ring i...

Jims #: 2467-1 Jims.005 oversize solid tappets can be only used with adjustable pushrods. Fitment: 1986-1999 FLST 1984-1998 FLT 1991-1998 FXD ...

Jims #: 2476-1 Jims.005 oversize solid adjustable tappet includes installed roller assembly Order adjuster screws and nuts separately. Fitment: 194...

Jims #: 973 This excellent tool upgrades Jims bearing installer tool for work on fine splined Twin Cam sprocket shafts. Allows for installation of ...

Jims #: 37047-91-5 · OEM #: 37047-91 Sprocket shaft Timken bearing installer tool is used to inst all crank shaft assemblies into crankcase. This t...

Jims #: 37047-91-6 Sprocket shaft Timken bearing installer tool is used to install crank shaft assemblies into crankcase. Tool is 2.500 inch long. ...

Jims #: 24017-80 · OEM #: 24017-80 Jims sprocket shaft nut is 1-1/8 inch-16 for taper end shaft. Fitment: 1972-1984 FL 1986 FLST 1979-1986 FLT...

Jims #: 97235-55B · OEM #: 97235-55B Sprocket shaft seal wrench tool installs and removes bearing nut on Big Twin models. Fitment: 1955-1969 FL In...

Jims #: 39361-69 Sprocket shaft seal and lock installers for Big Twins. Use with a bearing tool to help install seal. Notes:Order or bearing tool F...

Jims #: 24610-39 · OEM #: 24610-39, 416-39 Left side case race is machined and ground to factory specifications. Race has an outer diameter of 1.75...

Jims #: 2462-1 Jims standard hydraulic tappet has an outer diameter of.731 inch. Tappets are without internals. Order hydraulic unit separately. **...

Jims #: 2459-1 · OEM #: 18522-53PG Jims big axle power glide tappet assembly. Tappets have an outer diameter of.731 inch and are for Shovelhead eng...

Jims #: 18526-PG Jims power glide hydraulic standard tappet assembly include roller assembly installed. Designed for high performance motors. Tappe...