Transmission - Tools

Ultima #: 97-430 Ultima transmission 6 speed bearing installation tool holds bearing square to its bore eliminating marring of the bearing bore. Fi...

Ultima #: 97-428 Access door installation/removal tools is for use with Twin Cam H-D 6-speed cruise models. Fitment: 2006 FXD

Ultima #: 97-426 Ultima transmission door remover tool can be used with transmission in frame. Fitment: 2007 FLHT 2006 FXD 2007 FXST

Jims #: 901 Main drive gear remover tool removes the main drive gear from the main bearing while in the transmission case. This eliminates the need...

Jims #: 739 Jims bearing tool will install and remove the closed end countershaft bearing on 5 and 6 speed Big Twin transmissions without using a p...

Jims #: 95660-42 · OEM #: 95660-42, 12734-42 This mainshaft tool is used to install and remove the main seal in 4-speed transmissions. It will push...

Adjustable reamer kick starter shaft tool is to use to fit inner diameter on new bushings. Fitment: 1936-1940 EL 1941-1984 FL 1971-1984 FX 1...

Use this adjustable reamer to fit I.D. on new bushings. Measurements: Minimum O.D.: 15/16 inches Maximum O.D.: 1-1/16 inches Fitment: 1941-1984 F...

OEM #: 37842 Drive bearing press tool. Fitment: 1991-2006 FLST 1991-2006 FLT 1991-2006 FXST 1991-UP XL

4-speed main drive gear tool hex nut. *NOTE: Must order sleeve separately. Fitment: 1936-1952 EL 1941-1976 FL Installation instructions (PDF)

This mainshaft tool is used to install and remove the main seal in 4-speed transmissions. It will push the seal in as flat and straight as possible...

OEM #: 34902 Sifton mainshaft bearing race tool. *NOTE: Replacement parts like the race pusher tube are available separately. Fitment: 1986-2006 F...

Nut lock wrench collar features parkerized finish. Notes:Suggested to use with Counter Sprocket Nut Tool and Jims Countershaft Nut Sprocket Tool Fi...

Jims #: 972 This tool allows for perfect installation of the main drive gear oil seal on the assembled transmission to its proper depth. The protec...

Jims #: 998 Jims right side drive transmission access door puller tool removes the access door on all right sided drive transmissions. Fitment: 20...

Jack shaft lock wrench is zinc plated. This tool is used to hold starter gears on 1991-up Big Twins. Fitment: 1991-UP FL 1991-UP FLT 1991-UP F...

This 4-speed transmission arbor tool is what you need to replace the clutch hub nut to allow test rotation with 1/2 inch drill. Fitment: 1941-1984...

OEM #: 95600-33A Rear sprocket rivet tool will hold sprocket in place to install rivets by a hammer. This is a 5 piece set. Includes drum holder dr...

Jims #: 5830 Jims left main seal removal tool is for M8 models. Fitment: 2017-UP FLT 2018-UP FXST Installation instructions (PDF)

Jims #: 5517 Jims shifter mechanism sleeve is for removing and installing the shifter mechanism sleeve in M8 transmissions. The sleeve can be remov...

Jims #: 5810 Jims left main bearing oil seal installer assists with perfect installation and adds the advantage of allowing the alternator stator t...

Jims #: 5811 Jims balancer scissor gear alignment screw tool holds the two halves of the spring loaded scissor balancer gear in alignment before re...

Jims #: 2268 Jims main drive gear case seal installer tool ensures correct alignment and installs seal to the correct depth without damaging seal. ...

Jims #: 35316-80 · OEM #: 35316-80 Jims 5-speed main drive gear tool is used to remove and install the main drive gear. It also installs the main b...