Jims

Jims #: 18526-PG5 Jims power glide.005 hydraulic tappet assembly includes roller assembly installed. Order adjuster screws or nuts separately. Fitm...

Jims #: 33438-502 · OEM #: 33438-50, 2156-50 Kick starter gear bushing is.005 oversize. Fitment: 1936-1940 EL 1941-1984 FL 1971-1984 FX 1937...

Jims #: 35316-80 · OEM #: 35316-80 Jims 5-speed main drive gear tool is used to remove and install the main drive gear. It also installs the main b...

Jims #: 1133 7mm valve guide ream tool. Fitment: 2005-2017 FLST 2005-2016 FLT 2005-2017 FXD 2005-2017 FXST 2004-UP XL

Jims #: 1163 Use the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool ...

Jims #: 1011-36TB The cam bushing drill jig allows the installation and drilling of a dowel pin to factory location. Supplied with #31 drill by Jim...

Jims #: 1012-70TB The Jims cam bushing drill jig allows the installation and drilling of a dowel pin to factory location supplied with #31 drill by...

Jims #: 1017-37TB 1-3-4 cam bushing drill jig allows the installation and drilling of a dowel pin to factory location. Fitment: 1937-1948 UL 195...

Jims #: 25597-365 .005 oversize cam bushing Fitment: 1936-1940 EL 1941-1954 FL

Jims #: 1283 · OEM #: 42313 Cam chain unloader tool will hold the tension of the primary cam chain on the TC-88 model engine. Instructions included...

Jims #: 25588-575 Cam cover bushing for #2 cam. Bushing is.005 oversize for XL models. Fitment: 1957-1990 XL

Jims #: 25586-375 · OEM #: 25586-37, 660-37C Cam cover bushing is.005 oversize for #1 3 4 cams. Bushing fits Side Valve models. Fitment: 1937-1973...

Jims #: 96710-TL-5 Case lap head only has an outer diameter of 1-3/4 inch. Fitment: 0 All

Jims #: 96710-TL Jims case lap tool features a lap which is supported on both sides by a pilot on the bushing side and plate which locates on the c...

Jims #: 1707 · OEM #: 33805 The cleve block spreading tool facilitates installation of swingarms on rubber mount models. Fitment: 1980-UP FLT

Jims #: 1025-15 Race set is made from 52100 steel and hardened. Set is a 3 piece set. Fitment: 1930-1937 VL

Jims #: 24366-51K · OEM #: 24366-51, 301-51 Jims connecting rod roller retainer cage is a 4 piece set billet steel type. Fitment: 1936-1940 EL 1...

Jims #: 24335-36 .005 oversize bushings for piston pin. Set of two. *NOTE* Inside diameter must be reamed to proper size after installation. Measur...

Jims #: 1030-TS · OEM #: 23969-83 The Jims flywheel nut socket features a low profile to give 100% nut contact machined flat at nut receiving end t...

Jims #: 1075 The cylinder assembly tool allows for installation of stud to correct height. Fitment: 1986-1998 FLST 1984-1998 FLT 1991-1998 FXD...

Jims #: 23909-80 Jims sprocket shaft with 6° taper for late 1981-1986 Big Twin 80 inch are machined and hardened to factory specifications. *NOTE: ...

Jims #: 24001-30 · OEM #: 24001-30, 352-30 Jims sprocket shaft for 1930-1954 61 inch or 74 inch are machined and hardened to factory specifications...

Jims #: 24001-70 · OEM #: 24001-70 Jims sprocket shaft for 1970-1971 Big Twin 74 inch are machined and hardened to factory specifications. Fitment:...

Jims #: 2392 · OEM #: 2392 This accurate gauge allows the measuring of 90° when tightening head bolts. Also features torquing sequence lasered on g...