Jims

Jims #: 1776 Our Jims fork spring compressor tool puts pressure on top fork plug to compress spring to ease in assembly. Compressor can be mounted ...

Jims #: 2043 This Jims fork tube plug tool is used to remove and install top fork tube plugs. Eliminates possible burring of plug caused by wrenche...

Jims #: 968 This Jims 3 piece gasket locator tool will properly align the primary cam and transmission end cover gaskets that will prevent misalign...

Jims #: 2461-1 Jims big axle power glide hydraulic tappet only is.005 inch oversize for Shovelhead engines. Fitment: 1966-1984 FL 1979-1983 FLT ...

Jims #: 2464-1 Jims.005 oversize hydraulic tappet includes installed roller assembly. Order hydraulic unit and nuts separately. **NOTE: Tappet adju...

Jims #: 729 This tool safely removes and installs the inner primary bearing without damage to the new bearing. Also removes and installs inner prim...

Jims #: 23960-80A3 · OEM #: 23960-80A Jims crank pin is made of 8620 steel.062 heat treated penetration. Crank pin is 3 oil hole type. Fitment: 198...

Jims #: 23961-80A3 · OEM #: 23961-80A Jims crank pin features heat treating 60-62 RC to a case depth of.100 Crank pin is 3 oil hole type. Order nut...

Jims #: 23961-80AS Crank pin is made of 8620 steel with heat treating 60-62RC to a case depth of.100. A special 180° oiling design helps lubricate ...

Jims #: 23975-873 · OEM #: 23975-87 Jims crank pin features heat treating 60-62 RC to a case depth of.100. Crank pin is 3 oil type.002 oversize on ...

Jims #: 2244 · OEM #: 2244 Jims 35mm hex fork nut socket tool removes or installs the top fork nut and has a 3/8 inch drive. Tool has a rubber prot...

Jims #: 35625-79B · OEM #: 35625-79B Jims 4th gear countershaft for 5-speed stock ratio Fitment: 1986-1993 FLST 1979-1993 FLT 1991-1993 FXD ...

Jims #: 1147 · OEM #: 41771 Our Big Twin alternator rotor puller uses the sprocket shaft end to center the two threaded holes in the rotor to allow...

Jims #: 779 Used to hold the hydraulic tensioners in place when repairing Beta engines. Hydraulic tensioners are used to keep constant chain tensio...

Jims #: 1162 · OEM #: 43293-A Jims brake caliper piston remover tool will support the brake caliper pistons for removal holding the pistons square ...

Jims #: 1706 Jims breather ream tool repairs damaged breather gear holes. Using this tool will repair damaged breather hole to use a.030 oversize b...

Jims #: 1281 · OEM #: 42315 Jims bushing remover/installer tool will help remove and install bushings in cam support plate on TC-88 models. Fitment...

Jims #: 2280 · OEM #: 2280 Jims cam bearing and bushing alignment tool checks the alignment of cam bearing to cam cover bushing. Any binding of thi...

Jims #: 2188 · OEM #: 2188 Jims cam bearing installer tool presses the inner cam bearings smoothly into the right case with the bearings installed ...

Jims #: 1280 The Jims cam bearing puller tool is used to remove the bearing from the crankshaft and is designed to do this with no slipping or bind...

Jims #: 2281 Jims cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case. This tool is sturdy re...

Jims #: 1290 This alignment tool is designed to index the cam gears position while removing on installing the cam gear. You will be able to accurat...

Jims #: 1390 The cam gear remover tool is used to remove the cam gear from the camshaft. The tool acts as a stable base to keep the camshaft perpen...

Jims #: 994 The cam locking tool allows the removal and torquing of cam sprocket bolts by locking camshaft and camshaft sprockets. Fitment: 2007-2...