Engine

Goodson #: WR-378-G .378 valve guide ream tool Fitment: 0 All

Brush Research #: BC8M18 Valve guide flex hone tool 8mm Fitment: 1986-2004 FLST 1984-2004 FLT 1991-2004 FXD 1984-1994 FXR 1984-2004 FXST ...

Goodson #: WR-311-G .311 valve guide ream tool Fitment: 0 All

Goodson #: WR-310-G .310 valve guide ream tool Fitment: 0 All

Brush Research #: BC10M18 Valve guide flex hone tool 10mm Fitment: 1941-1984 FL 1971-1984 FX

OEM #: 94819-02 Replica tool kit contains 10mm 1/4 inch 1/2 inch 9/16 inch 5/8 and 3/4 inch wrenches. 3/16 inch 1/4 inch 5/16 inch 3/8 inch 5/32 in...

Jims #: 1710 Snap ring remover tool will remove the Timken bearing outer race snap ring without damage to the case. You can replace the snap ring i...

Needle bushing tool positions pinion bushing in cam cover. Fitment: 1970-1984 FL 1986-1998 FLST 1979-1998 FLT 1971-1984 FX 1991-1998 FXD ...

Jims #: 1706 Jims breather ream tool repairs damaged breather gear holes. Using this tool will repair damaged breather hole to use a.030 oversize b...

Jims #: 2392 · OEM #: 2392 This accurate gauge allows the measuring of 90° when tightening head bolts. Also features torquing sequence lasered on g...

Jims #: 2280 · OEM #: 2280 Jims cam bearing and bushing alignment tool checks the alignment of cam bearing to cam cover bushing. Any binding of thi...

Jims #: 2281 Jims cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case. This tool is sturdy re...

Jims #: 2233 Jims tappet screw plug tool is used to remove tappet oil filter screen plug without removing exhaust pipes. Fitment: 1953-1984 FL 1...

Jims #: 2237 Jims pin gear lock tool is used when applying torque to the pinion nut. Align underneath gear and screw into case. Fitment: 1954-1984...

Jims #: 1001 Jims 3 piece valve guide driver tool kit is for the use of guide removal and installation on all models. Fitment: 0 All Installation ...

Jims #: 2324 Jims sprocket shaft seal installer tool is designed to install sprocket shaft seal to proper depth and for holding the seal perfectly ...

Jims #: 2188 · OEM #: 2188 Jims cam bearing installer tool presses the inner cam bearings smoothly into the right case with the bearings installed ...

OEM #: 39958 Pinion bearing race removal tool is used to remove and install the outer race on 1958 and later models. Fitment: 1958-1984 FL 1986-...

OEM #: 39782 Cylinder head support stand. Adapters are to be used with a bar press and that is included to push guides in and out in a straight lin...

Ring-o-matic ring compressor tool kit The sizes for this ring compressor tool are as follows: 2-7/8 inch - 3-1/8 inch 3-1/8 inch - 3-3/8 inch 3-3/8...

Piston ring installer plier tool Fitment: 0 All

Brush Research #: GB31418 3 inch - 3-3/16 inch cylinder flex hone tool has a 13-1/2 inch overall length. This flex hone tool is used to finish and ...

Lisle Corp. #: 21200 Valve grinding stick tool is for hand grinding valves. Synthetic rubber vacuum cup is resistant to oil grease and gasoline. Cu...

Brush Research #: BC14M18 Rocker arm bush ball hone tool.554 Fitment: 1966-1984 FL 1986-2017 FLST 1979-UP FLT 1971-1984 FX 1991-2017 FXD ...