Engine

DIY Touring tool kit for 2017 FLT models. Kit includes rider tools and service tools for the rider-mechanic. This DIY tool kit will help the rider ...

Jims #: 5831 Jims castle nut socket is for use with FXST inverted forks. 2017-up Softail models requires the castle nut to secure and compress the ...

Jims #: 1051 To remove and replace wrist pin bushing without removing connecting rods from crankcase use the Jims TC-88 connector rod bushing tool....

OE #: HD-41506 · OEM #: 41506 OE crankshaft locking tool fits 1991-1999 XL models by engaging the pinion shaft splines. This allows removal and tor...

OEM #: 96830-51 Tool is used for installation and removal of the pinion gear. Can be used to install gear on 1951-1953 Big Twin 61 inch and 74 inch...

Flute tap tool 1/8 inch-27 NPT thread features 5 flutes with a bright cobalt finish. Fitment: 0 Custom

Flute tap tool 3/8 inch-18 NPT thread features 4 flutes with a bright cobalt finish. Measurements:Overall Length: 2.5625 inches Fitment: 0 Custom

Jims #: 5506 Jims magnetic tappet holder tool set holds the tappets up while changing cams cam support plate or oil pump on all TC-88 and M8 engine...

Sifton outer primary cover starter bearing removal tool removes 9063 Torrington needle bearing for Big Twin and XL covers. *NOTE: This tool will al...

Oil pump relief valve ball reseat tool. This tool will facilitate ball burnishing of the relief valve seat on oil pumps. Fitment: 1936-1940 EL 1...

Flywheel fixture center tool is for use on hand wheel. Thread pitch is 5/8 inch-11. Fitment: 2000-2017 FLST 2000-UP FLT 2000-2017 FXD 2000-2...

Sifton cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case. This tool is sturdy reliable and ...

Flywheel fixture center tool is a replacement for the wheel bearing puller/installer tool. Thread pitch is 7/8 inch-14. *NOTE: Attaches to the flyw...

Jims #: 5504 Jims tappet position holding tool for Twin Cam and Sportster engines. This tool allows the tappets and anti-rotation pins to be safely...

Motorcycle roller dolley lift holds up to 1250 lbs. *NOTE: Hardware included. **NOTE: Delivered by truck only. Measurements: Overall Length: 78.74 ...

OEM #: 94086-09 Pushrod cover removal and installation tool fits TC-88 models. Fitment: 1999-2017 FLST 1999-UP FLT 1999-2017 FXD 1999-2017 F...

This flywheel truing hammer is a three pound lead/steel hammer that lasts longer than a lead hammer and is still soft enough so that it will not ma...

You can never go wrong with this tool kit. It is supplied appropriately for each year model and includes a tool bag. The entire kit fits inside tea...

OEM #: 33443 Use to align tappet block to engine case and also aligns oil pump to cam plate. Sold as a pair. Fitment: 1999-2017 FLST 1984-2016 F...

S&S Cycle #: 53-0013 The oil pump drill fixture allows drilling of cases to accept late model stock or S&S oil pumps. Fitment: 1936-1940 E...

Eastern #: A-94812-37A · OEM #: 94812-37A This eastern bushing reaming tool fits pinion bushing in cam cover. Measurements: Ream Diameter: 5/8 inch...

Eastern #: A-94805-80A · OEM #: 94805-80A This eastern bushing reaming tool is used to ream the pinion bushing in the cam cover to size. Pilots fro...

Sifton pushrod adjustment gauge for use on Big Twins with hydraulic lifter. Comes complete with instructions. With this gauge in place you will be ...

Eastern #: A-94814-80A · OEM #: 94814-80A This eastern bushing reaming tool fits pinion bushing in cam cover. Fitment: 1955-1957 FL