Engine

Pingel #: 62082 The Pingel head holder tool has 12 and 14mm ends to hold the head through spark plug hole by support in a vise. The Pingel head hol...

Jims #: 1047-TP This removal tool is used to press flywheels from cases press cases apart and break the sealant bond easily and safely. Fitment: 0 ...

Eastern #: A-94800-94 · OEM #: 38871 The crankshaft bushing plate pilot and reamer reams in board camshaft and camshaft crankcase bushing. Fitment:...

Jims #: 96710-TL Jims case lap tool features a lap which is supported on both sides by a pilot on the bushing side and plate which locates on the c...

Jims #: 95760-TP This pinion bushing puller tool is used to remove the pinion bushing from the cam cover. Fitment: 1954-1984 FL 1986-1998 FLST ...

Eastern #: 96728-77 Engine type lap head pilot tool sold by the each and for Eastern tool only. Fitment: 0 Replacement

Jims #: 1018-37TB The cam and pinion bushing drill jig tool allows the installation and drilling of a dowel pin to factory location. Fitment: 1936...

Jims #: 1045-TS Jims Timken bearing remover tool removes the bearing from the shaft without removing the shaft from the flywheel. Fitment: 1955-19...

Jims #: 1011-36TB The cam bushing drill jig allows the installation and drilling of a dowel pin to factory location. Supplied with #31 drill by Jim...

Jims #: 1017-37TB 1-3-4 cam bushing drill jig allows the installation and drilling of a dowel pin to factory location. Fitment: 1937-1948 UL 195...

Jims #: 94804-57 · OEM #: 94804-57 The Jims rocker arm bushing reamer tool is used to ream rocker bushings to a factory fit of.0007 inch-.0012 inch...

Jims #: 1030-TS · OEM #: 23969-83 The Jims flywheel nut socket features a low profile to give 100% nut contact machined flat at nut receiving end t...

Eastern #: A-94802-36 · OEM #: 94802-36, 12134-36 Eastern cam bushing reaming tool is used to ream the cam bushing in the crankcase. Measurements: ...

Eastern #: A-99030-94 This plug tool allows the setting of proper end play by selection of proper spacer. Use when refitting bearings or bearing se...

OEM #: 96600-36B The Sifton valve spring compressor tool is a must when doing valve work. Fitment: 1935-1940 EL 1941-1984 FL 1986-1998 FLST ...

Jims #: 1013-54TB The Jims pinion bushing jig tool allows the installation and drilling of a dowel pin to factory location supplied with #31 drill ...

Eastern #: A-94803-52 · OEM #: 94803-52 Eastern 1-3-4 cam cover bushing. Measurements:Ream Diameter: 11/16 inches Fitment: 1952-UP XL

Jims #: 1012-70TB The Jims cam bushing drill jig allows the installation and drilling of a dowel pin to factory location supplied with #31 drill by...

The Sifton valve spring tool is bench mounted to compress springs on engines and also used for checking valve travel and coil bind of the valve spr...

Thexton #: 432 MIN 12 The 4 piece Universal thread gauge set identifies USS Metric pipe size and spark plug size. Fitment: 0 All

Jims #: 37047-91-5 · OEM #: 37047-91 Sprocket shaft Timken bearing installer tool is used to inst all crank shaft assemblies into crankcase. This t...

K-Line #: KL1402F Valve seal sleeve 11/32 inch 10 pack. Fitment: 1957-2003 XL

Jims #: 37047-91-6 Sprocket shaft Timken bearing installer tool is used to install crank shaft assemblies into crankcase. Tool is 2.500 inch long. ...

OEM #: 96780-58A Piston pin lock tool. Fitment: 1952-1972 FL 1971-1972 FX 1952-1972 XL