All V-Twin Parts

The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 3/8 inch drive ratchet. For use on O2 sensors that ha...

The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 7/8 inch wrench or a 3/8 inch drive ratchet. For use ...

OEM #: 91573-09A This black center stand bolts directly to the FLT model frame. It lifts the bike upright and stands by activating the lever on the...

OEM #: 91573-09A This chrome center stand bolts directly to the FLT model frame. It lifts the bike upright and stands by activating the lever on th...

Ultima #: 91-104 Clear timing hole plug with knurled knob for a non-slip installation. Fitment: 0 All

Jims #: 5838 Jims oil pump alignment tool is the perfect aid for the technician to either assemble as individual components with supplied studs or ...

DIY Touring tool kit for 2017 FLT models. Kit includes rider tools and service tools for the rider-mechanic. This DIY tool kit will help the rider ...

This rocker box breather upgrade includes breather tubes only. Set of two. Notes:Replacement part for Rocker Box Breather Tool Kit. Fitment: 1992-...

Rod alignment plate features a cast iron construction with a parkerized finish for Big Twin engines. Fitment: 1936-1952 EL 1941-1985 FL

Jims #: 5831 Jims castle nut socket is for use with FXST inverted forks. 2017-up Softail models requires the castle nut to secure and compress the ...

OEM #: 96830-51 Tool is used for installation and removal of the pinion gear. Can be used to install gear on 1951-1953 Big Twin 61 inch and 74 inch...

OE #: HD-41506 · OEM #: 41506 OE crankshaft locking tool fits 1991-1999 XL models by engaging the pinion shaft splines. This allows removal and tor...

Jims #: 1147 · OEM #: 41771 Our Big Twin alternator rotor puller uses the sprocket shaft end to center the two threaded holes in the rotor to allow...

Jims #: 1051 To remove and replace wrist pin bushing without removing connecting rods from crankcase use the Jims TC-88 connector rod bushing tool....

Flute tap tool 3/8 inch-18 NPT thread features 4 flutes with a bright cobalt finish. Measurements:Overall Length: 2.5625 inches Fitment: 0 Custom

Flute tap tool 1/8 inch-27 NPT thread features 5 flutes with a bright cobalt finish. Fitment: 0 Custom

Jims #: 5506 Jims magnetic tappet holder tool set holds the tappets up while changing cams cam support plate or oil pump on all TC-88 and M8 engine...

Sifton cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case. This tool is sturdy reliable and ...

Sifton outer primary cover starter bearing removal tool removes 9063 Torrington needle bearing for Big Twin and XL covers. *NOTE: This tool will al...

Flywheel fixture center tool is for use on hand wheel. Thread pitch is 5/8 inch-11. Fitment: 2000-2017 FLST 2000-UP FLT 2000-2017 FXD 2000-2...

Includes three interchangeable adaptors to service all carburetors to remove venturis. The 1-3/16 inch collar is used for M-4 ll 16 and 18 carburet...

Oil pump relief valve ball reseat tool. This tool will facilitate ball burnishing of the relief valve seat on oil pumps. Fitment: 1936-1940 EL 1...

Flywheel fixture center tool is a replacement for the wheel bearing puller/installer tool. Thread pitch is 7/8 inch-14. *NOTE: Attaches to the flyw...

Jims #: 5504 Jims tappet position holding tool for Twin Cam and Sportster engines. This tool allows the tappets and anti-rotation pins to be safely...