Tools

Jims #: 785 Allows the engine builder to check flywheel run out of the pinion shaft while assembled in the engine case. Also allows the checking of...

Duo-glide jack stand is a 2 piece factory tool that fits in oval tool boxes. Lifts up the right side of the frame under the oil tank. There is a tu...

This 2 piece parkerized sprocket rivet tool set includes one rivet set for heading rivet and one dowel punch to align the rivet so the sprocket and...

Axle locker tool acts as a third hand to help hold the left side welded axle nut. With this third hand axle tool you will no longer need to find a ...

Hollow axle plug tool Sold as a pair. Fitment: 2008-2017 FXD 2008-2017 XL

Conical valve spring adapter tool has 5/16 inch-18 thread. Notes:Suggested to use with Bench Valve Spring Tool. Fitment: 2005-2017 FLST 2005-201...

Jims #: 2312 Jims primary locking tool is used to lock primary for service work. Fitment: 2007-2016 FLT Installation instructions (PDF)

Jims #: 937 Shoulderless valve guide drive tool handle only will remove shoulderless valve guides including the 7mm size guides. Use driver handle ...

Jims #: 938 This valve guide installer takes the guess work out of valve guide installation while insuring that the valve guides are installed to p...

Conical valve spring adapter tool has 7/16 inch thru hole. Notes:Required to use with Valve Spring Compressor Tool Fitment: 2005-2017 FLST 2005-...

Jims #: 955 Jims fuel pressure test gauge tool includes the hose connectors and fittings to safely perform a fuel pressure test. Detailed instructi...

Jims #: 947 Jims rear wheel compensator bearing tool used to remove or install the ball bearing in rear pulley on FLT models. Tool will center and ...

Rivera-Primo Products #: 1062-0003 York-Pro clutch puller tool attaches to all Rivera pro-clutches or Primo belt drives diaphragm spring style clut...

Tap tool 1/4 inch x 24 inch is used for closed-end hole threading. Fitment: 0 All

Fork stem die holder is for use with a 1.966 inch outer diameter die tool. Measurements:Inner Diameter: 1.966 inches Notes:For use with 1inch Fork ...

OEM #: 90205 1/4 inch x 40 inch tap tool for Linkert carburetors. Fitment: 1941-1965 FL

OEM #: 62700199 Oil catcher pan is used when removing the oil filter to avoid spilling the oil onto the engine cases. There is a 12 inch tube to di...

Evolution rocker box wrench tool Fitment: 1986-1999 FLST 1984-1998 FLT 1991-1998 FXD 1984-1994 FXR 1984-1999 FXST

Sifton #: 77967 Sifton wrist pin bushing reamer tool is easy to use with their design lead in taper at the start of each ream. Order rod clamping t...

Wrist pin ring tool easily installs and removes wrist pin clips without damage. Tool works on all pistons with retaining ring dimple. Fitment: 199...

OE #: 62700239 · OEM #: 62700239 OE primary oil fill funnel allows the oil to be added to the primary cover with no mess or spills. This funnel sna...

8 Gauge spoke wrench tool Each end of wrench fits 6.2 and 6.4 size spokes. Fitment: 0 All

Orange funnel set includes a 9 inch transmission crankcase fill funnel primary case oil fill funnel and a drip free oil filter funnel. Sold as a 3 ...

4-speed clutch hub puller tool is the swivel style with the inchT inch bar included to allow the removal of the hub without removing the clutch pus...