Tools

OEM #: 96780-58A Piston pin lock tool. Fitment: 1952-1972 FL 1971-1972 FX 1952-1972 XL

Jims #: 39361-69 Sprocket shaft seal and lock installers for Big Twins. Use with a bearing tool to help install seal. Notes:Order or bearing tool F...

K-Line #: KL1402F Valve seal sleeve 11/32 inch 10 pack. Fitment: 1957-2003 XL

Jims #: 1010 The piston pin align tool is used to check straightness of the rod without removing rods from case. Tool is 4-1/2 inch long. Fitment: ...

Jims #: 1707 · OEM #: 33805 The cleve block spreading tool facilitates installation of swingarms on rubber mount models. Fitment: 1980-UP FLT

This link press tool presses the side plates on all 530 o-ring chains. Fitment: 0 All

Sifton #: B-2062 Sifton pushrod cover compressor tool allows removal and installation of pushrod clip. Fitment: 1936-1940 EL 1941-1984 FL 1986...

Eastern #: A-96716-40 · OEM #: 96716-40 1-3/8 inch lap head pilot tool engine type. For Eastern tool only. Fitment: 1955-1957 FL 1929-1973 G

Eastern #: A-96715-40 · OEM #: 96715-40 1-1/2 inch lap head pilot tool is the engine type. *NOTE: For Eastern tool only. Fitment: 1936-1952 EL 1...

Eastern #: A-96727-56 · OEM #: 96727-56 1-1/4 inch lap head pilot tool is the engine type for the Eastern tool only. Fitment: 1956-1969 FL

4-speed inch88 inch roller spacer tool is used to mimic the 88 roller spacing setting end play. Notes:Suggested to use with 4 Speed Main Drive Gear...

Gasket alignment stud tool set includes two 1/4 inch x 20 and two 1/4 inch x 24 threaded studs with slotted screw head. Install to hold oil pump ga...

4-speed main drive gear tool hex nut. *NOTE: Must order sleeve separately. Fitment: 1936-1952 EL 1941-1976 FL Installation instructions (PDF)

Jims #: 5534 Jims compensator bolt torx socket is for 2014-up Big Twins. Used to remove or install the compensator bolt. Fitment: 2014-2017 FLST ...

V-Twin compensator sprocket wrench is used to easily install or remove compensating sprockets. Features 1/2 inch drive. Fitment: 1955-1969 FL

This mainshaft tool is used to install and remove the main seal in 4-speed transmissions. It will push the seal in as flat and straight as possible...

OEM #: 34902 Sifton mainshaft bearing race tool. *NOTE: Replacement parts like the race pusher tube are available separately. Fitment: 1986-2006 F...

OEM #: 12074-39 Black oxide finish backing washer #17 puller tool. Notes:Suggested to use with Wheel Bearing Puller/Installer Tool. Fitment: 2000-...

Mini air compressor features a compact design to fit inside a saddlebag or car. Includes 2' of hose and end to fill tire valves up to 35 pounds. *N...

Chain puller tool. Fitment: 0 All

Clutch compression tool has adapter included Fitment: 1990-2017 FLST 1990-UP FLT 1991-2017 FXD 1990-1994 FXR 1990-2017 FXST 1991-UP XL ...

Nut lock wrench collar features parkerized finish. Notes:Suggested to use with Counter Sprocket Nut Tool and Jims Countershaft Nut Sprocket Tool Fi...

Pingel #: WC350 The wheel chock features quick mounting and removal by sliding in and out of slotted mount pads and secures a motorcycle on your wo...

Linkert tool kit includes 6 special drills with brass knurled handles 1 idle shot tool and 1 venturi tool for use on brass linkert carburetor bodie...