Engine

OEM #: 26325-49, 691-49 Oil pump scavenger idler gear. Idler oil pump gear does not include oil grove or oil rotor drive slot. *NOTE: 1942-1949 pum...

Kit includes oil pressure switch fitting pressure switch straight male gas/oil fitting oil pump check valve spring 3/8 inch clutch ball bearing dra...

OEM #: 26326-62A Oil pump idler gear. This gear is used as the scavenger idler gear on late 1962-1967 models and as the feed idler gear on the 1968...

OEM #: 26315-48, 688-48 Oil pump drive feed gear. Measurements: Outer Diameter: 0.990 inches Inner Diameter: 7/16 inches Thickness: 0.380 inches F...

OEM #: 26320-36, 690-36 Scavenger oil pump gear drive. Measurements: Outer Diameter: 0.990 inches Inner Diameter: 7/16 inches Thickness: 0.500 inch...

OEM #: 26317-62 Oil pump feed idler gear. Measurements: Outer Diameter: 0.990 inches Inner Diameter: 7/16 inches Thickness: 0.380 inches Fitment: ...

OEM #: 8854, 0279 Steel pushrod ball bearing 3/16 inch. Sold as a pack of 50. Fitment: 1948-1952 FL

OEM #: 26317-48, 689-48 Oil Pump Feed Idler Gear. This gear has a 1/4 inch extended bearing area past the level of the gear that extends into the c...

Tappet oil screen kit includes chrome plug screen o-ring and spring. Fitment: 1963-1965 FL

Tappet oil screen kit includes screen housing body ball spring washer and cadmium plug. Fitment: 1952-1962 FL Installation instructions (PDF)

Eastern #: A-25276-52 · OEM #: 25276-52 Stock replacement type oil pump screen. Fitment: 1954-1956 K 1957-1973 XL

Tappet oil screen kit includes chrome cap screen o-ring and spring for Shovelhead. Fitment: 1966-1969 FL

Tappet oil screen kit with chrome top plug includes screen o-ring and spring. For Shovelhead and Evolution. Fitment: 1981-1984 FL 1986-1999 FLST...

Tappet oil screen kit includes chrome cap screen o-ring and spring for Shovelhead Fitment: 1970-1980 FL 1970-1983 FX

S&S Cycle #: 33-5175 Chain type kit includes cam cover gasket two inner cam bearings two outer cam bearings and a retaining ring. Fitment: 200...

S&S Cycle #: 106-5896 Gear type kit includes cam cover gasket two inner cam bearings two outer cam bearings and a retaining ring. Fitment: 200...

Oil pump governor cover kit includes a cast parkerized cover with the chain oiler provision and an internal rotator governor. Usually found on Army...

Shim is machined and assures proper spring pre load raising and stabilizing volume and pressure. Fitment: 1999-2017 FLST 1999-2016 FLT 1999-20...

Cast oil pump cover for Knucklehead and early Panhead models features a parkerized finish. Oil pump cover features provision for chain oiler on 194...

Kit includes pinion shaft gear steel spacer ring spacer cam chest breather screen and separator plate. This is a 4 piece kit. Fitment: 1955-1969 FL

Pinion shaft hardware kit includes pinion shaft key keyed oil pump drive gear 21 tooth pinion shaft gear pinion shaft nut an inside pinion shaft nu...

Kit includes pinion shaft seal ring gear spacer ring spring cam chest breather screen and separator plate. This is a 5 piece kit. Fitment: 1936-19...

Chrome oil pump cover for models without chain oiler. Order allen screws separately. Fitment: 1968-1984 FL 1986-1991 FLST 1979-1991 FLT 1971...

XL oil pump kit includes a billet aluminum body with pins and 4 gears installed. Fitment: 1972-1976 XL