Tools

Oil drain spigot tool with a red anodized finish keeps the fluid off of the frame. This tool channels the transmission fluid from the bottom of you...

Needle jet seat cutter tool is for use on CV Keihin carburetors. It eliminates gasoline seepage from around the needle jet and creates a smooth and...

OEM #: 63794-10 Oil catcher pan is used when removing the oil filter to avoid spilling the oil onto the engine cases. There is a 12 inch tube to di...

OE #: 63797-10 · OEM #: 63797-10 OE primary oil fill funnel allows the oil to be added to the primary cover with no mess or spills. This funnel sna...

OE #: 62700015 · OEM #: 62700015 OE Primary oil fill funnel allows the oil to be added to the primary cover with no mess or spills. This funnel sna...

3/4 inch X 16 tap tool. Fitment: 1936-1948 EL 1941-1948 FL 1936-1957 G 1936-1952 W

OEM #: 97019-52A Replica shock absorber compressor tool simplifies shock absorber disassembly or assembly by holding the spring in compression whil...

13 in 1 folding tool kit. This tool includes: 3-Hex: 5/32 - 3/16 - 1/4 inch 2-Torx: T25-T27 2-Screwdriver: 205 2-Open Wrench: 10mm - 12 point box 9...

K&L Supply Co. #: 35-7568 Adjustable fork seal driver tool kit includes 1 split seal driver and 3 seal guides sizes 35mm 39mm and 41mm. This se...

Lower fork bearing removal tool includes cross arm puller rods and lower puller claw. To use the tool remove roller from old bearing install claw a...

OEM #: 12047-36 Headbolt wrench is for use on a 12 point 9/16 inch headbolt. Fitment: 1936-1940 EL 1941-1984 FL 1971-1984 FX

K&L Supply Co. #: 35-8885 This valve fishing tool combines core driver and deflating pin with a full length cable to facilitate working the val...

OEM #: 33416 Driver tool handle only for sprocket shaft bearing tool. For wheel and sprocket shaft races. For use with split bearing race extractor...

OEM #: 34761 The clutch compressor tool allows for disassembly of the clutch pack easily. Fitment: 1985-1990 XL

OEM #: 94547-80A, 94547-80B Sprocket shaft bearing tool removes and installs engine sprocket shaft bearings from crankcase. Tool is a 2 part set. S...

OEM #: 34733 Countershaft bearing install tool for 41mm bushing and seal installation. Fitment: 1977-1984 FL 1977-1984 FX

OEM #: 34634 Fork bushing and seal installer installs bushings and seals without damaging components on 41mm forks. Fitment: 1986-2017 FLST 1984...

Eastern #: A-99285-93 · OEM #: 34190 Fork bushing and seal installation tool installs bushing and seals without damaging components. Notes:Inside d...

Sifton #: 97-420 · OEM #: 94660-37A Sifton center nut wrench tool is a heavy duty thick wall tube extra long. Tool has a 2 piece design a inner col...

Universal fork stem die tool with holder is used for repairing or dressing 1 inchx 24 TPI on Big Twin fork stems. Holder can be turned by wrench. F...

OEM #: 97087-65A Hose clamp crimping plier Fitment: 0 Custom

This is a hand held device which quickly cuts any size rubber or nylon hose up to 1-1/4 inch diameter leaving the hose perfectly clean and square. ...

Eastern #: A-97194-77 Bearing race press plug tool is used to remove and install Timken bearing outer race. Fitment: 1977-2003 XL

Eastern #: A-97194-54 Bearing race press plug tool is used to remove and install Timken bearing outer race. Fitment: 1957-1976 XL