Engine

Jims #: 1010 The piston pin align tool is used to check straightness of the rod without removing rods from case. Tool is 4-1/2 inch long. Fitment: ...

Jims #: 39361-69 Sprocket shaft seal and lock installers for Big Twins. Use with a bearing tool to help install seal. Notes:Order or bearing tool F...

Sifton #: B-2062 Sifton pushrod cover compressor tool allows removal and installation of pushrod clip. Fitment: 1936-1940 EL 1941-1984 FL 1986...

4-speed inch88 inch roller spacer tool is used to mimic the 88 roller spacing setting end play. Notes:Suggested to use with 4 Speed Main Drive Gear...

Eastern #: A-96727-56 · OEM #: 96727-56 1-1/4 inch lap head pilot tool is the engine type for the Eastern tool only. Fitment: 1956-1969 FL

Eastern #: A-96715-40 · OEM #: 96715-40 1-1/2 inch lap head pilot tool is the engine type. *NOTE: For Eastern tool only. Fitment: 1936-1952 EL 1...

Eastern #: A-96716-40 · OEM #: 96716-40 1-3/8 inch lap head pilot tool engine type. For Eastern tool only. Fitment: 1955-1957 FL 1929-1973 G

Gasket alignment stud tool set includes two 1/4 inch x 20 and two 1/4 inch x 24 threaded studs with slotted screw head. Install to hold oil pump ga...

Jims #: 5534 Jims compensator bolt torx socket is for 2014-up Big Twins. Used to remove or install the compensator bolt. Fitment: 2014-2017 FLST ...

Mini air compressor features a compact design to fit inside a saddlebag or car. Includes 2' of hose and end to fill tire valves up to 35 pounds. *N...

Linkert hand tool tap 5/16 inch X 18 thread. Fitment: 1941-1965 FL

Linkert hand tool tap 12-24 thread. Fitment: 1941-1965 FL

Linkert hand tool tap 5/16 inch X 32 thread. Fitment: 1941-1965 FL

This four piece tool safely installs the inner cam bearings to the proper depth in the case without damaging bearings. Complete 8 piece tool set in...

Linkert hand tool tap 10-32 thread. Measurements: Overall Length: 3.9370 inches Shank Diameter: 0.4375 inches Fitment: 1941-1965 FL

Cam bearing puller tool removes the inner cam needle bearing #9057 without splitting the cases while preventing the rollers from coming out during ...

Cam bearing remover tool allows the removal of needle bearings while keeping the needles from falling into the engine. For use with bearing as list...

Jims #: 959 Using the special Jims precision insert this tool is designed to easily and accurately convert the left side crank roller bearing to th...

Jims #: 975 This Jims shaft turning tool fits spline or taper on assembled motor and allows engine to be turned over by 1/2 inch ratchet or impact ...

Jims #: 973 This excellent tool upgrades Jims bearing installer tool for work on fine splined Twin Cam sprocket shafts. Allows for installation of ...

Jims #: 968 This Jims 3 piece gasket locator tool will properly align the primary cam and transmission end cover gaskets that will prevent misalign...

Jims #: 995 Use this tool to expertly and safely break the case sealant by pushing apart both halves. This tool bolts to the primary mounting holes...

Jims #: 994 The cam locking tool allows the removal and torquing of cam sprocket bolts by locking camshaft and camshaft sprockets. Fitment: 2007-2...

This eight piece set features exact replicas of tools as available to dealers in the early days. Fitment: 1936-1952 EL 1941-1984 FL 1941-1957 ...