Engine

OEM #: 96650-30, 11962-X Truing machine features cast iron construction and is designed to true stock style flywheels. For fork tube straightness c...

Mini motorcycle lift includes wheel cart tool. Mini lift is removable from the cart. Capacity is 1100lbs minium height is 5.3 inch and maxiumum hei...

Brush Research #: GBD33418 3-5/8 inch - 3-3/4 inch cylinder flex hone tool has a 13-1/2 inch overall length. This flex hone tool is used to finish ...

Brush Research #: GBD40018 4 inch cylinder flex hone tool is has a 13-1/2 inch overall length. This flex hone tool is used to finish and deglaze bl...

Brush Research #: GBD41418 4-1/4 inch cylinder flex hone tool is designed for 3-1/4 inch thru 4-5/8 inch bore diameters. This flex hone tool is use...

Left side case repair ring is for TC-88 engines at inner primary. Fitment: 1999-UP FL 1999-2017 FXST

Mini motorcycle lift tool features stir ups for frame rails. Tool is operated with a inchT inch handle which is included. Fitment: 0 All

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a Big Twin and T...

Valve seat wheel is 1.875 inch-45°. Fitment: 0 Custom

Sifton #: TD16-0519 Sifton oil pump check valve ball re-seater tool will recut the seat to allow the ball to sit properly to prevent sumping for Bi...

Mini motorcycle lift tool. Measurements: Length: 14-1/2 inches Width: 9' Height: 3-3/4 inches Fitment: 0 All

Use the lift on the table or floor to free wheels. 1000 lb capacity with rubber padded top. Mini bike life tool has a wide stance and fully rubberi...

Engine stand stool for a TC-88 engine. Fitment: 1999-2017 FLST 1999-2016 FLT 1999-2017 FXD 1999-2017 FXST

Engine stand is to be used with Big Twin engines. Features the V-Twin orange! Base is 2 flat steel plates for mounting to bench. *NOTE: Does not us...

Left rear lower motor mount bolt nut wrench tool. Allows removal and installation of left rear motor mount bolt nut without removing the inner prim...

Engine stand is to be used on Ironhead and Evolution style XL motors. Engine stand measures 15-1/4 inch from the plate to the front holes. *NOTE: D...

Cross arm puller tool is a 1 inch square bar 4-3/4 inch long and slotted with 3/8 inch x 16 bolts. Use any size bolt to pull gears and sprockets th...

Engine stand is to be used with Big Twin engines. *NOTE: Does not use an auto engine stand. Measurements:Bottom to top Height: 8-1/4 inches Fitment...

Sifton 3 piece factory tool set includes a connecting rod clamping tool wrist pin bushing reamer tool and installer and the precision reamer. The p...

Rotating / tilt engine stand for Big Twins. *NOTE: Customer must install washers and/or bushings not included at pivot points behind knobs to secur...

Kibblewhite #: 20-20833 Valve guide seal installation tool is manufactured from high strength 6061-T6 aluminum for increased durability when compar...

Kibblewhite #: 20-20832 Valve guide seal installation tool is manufactured from high strength 6061-T6 aluminum for increased durability when compar...

Kibblewhite #: 20-20830 Valve guide seal installation tool is manufactured from high strength 6061-T6 aluminum for increased durability when compar...

Kibblewhite #: 20-20831 Valve guide seal installation tool is manufactured from high strength 6061-T6 aluminum for increased durability when compar...