Electrical - Magneto

Magneto rotor kit includes upper and lower bearing. Rotor has permanent magnets cast in as original. For use with all Morris and Joe Hunt magneto b...

Accel #: 64272 · OEM #: 29533-55A Magneto point set is made in the USA from the finest materials and designed for high quality and reliability. Fit...

OEM #: 29646-62 Ignition ground lock includes two keys insulator block wire ball spring and key switch assembly. Includes key lock and plastic insu...

OEM #: 29625-55 Ground terminal wire. NOTE: Distributor top is original design with the spring clip fastener. Top is not interchangeable with early...

OEM #: 29625-62 Ground terminal wire. Fitment: 1962-1965 XLCH

OEM #: 29620-55 Breaker arm spring clip. Fitment: 1958-1965 XLCH

OEM #: 29622-55A Rotor shaft end spring clip. Fitment: 1958-1965 XLCH

OEM #: 29607-65 Zinc plated magneto control arm is for Fairbanks Morse and most aftermarket units. Fitment: 1965-1969 XLCH

OEM #: 29601-48 Magneto adapter plate screw kit features cadmium plated screws. Fitment: 1958-1962 XLCH

OEM #: 27450-36, 3370-36 Carburetor throttle lever wire block has a cadmium finish. For use wuth Linkert and Bendix carburetors. Fitment: 1936-194...

Eastern #: A-35838-55 Transmission countershaft thrust washer.085 Fitment: 1955-1956 K 1957-1984 XL

OEM #: 29550-56R XR magneto gasket set is for forward mount magnetos. Sold as a set of 2. Fitment: 1950-UP KR 1950-UP WR 1950-UP XL

James #: JGI-29550-55 · OEM #: 29550-55 James magneto cap paper gasket Fitment: 1958-1969 XLCH

OEM #: 29550-55 Magneto neoprene cap gasket. Gasket is for Morris Joe Hunt and Fairbanks Magnetos. Fitment: 1957-1970 XL

OEM #: 29602-56R XR magneto adapter plate gasket for use on 1970-1980 XR models. Sold as a pack of 10. Fitment: 1970-1980 XR

Gary Bang #: 63460 · OEM #: 29550-55 Magneto Paper Cover Gaskets Fitment: 1958-1969 XLCH

OEM #: 29603-48 Timer seal ring housing is molded rubber. Sold in a pack of 10. Fitment: 1965 FL 1958-1965 XL

OEM #: 29630-55 This rotor shaft end seal is molded rubber. Measurements: Outside diameter: 1.25 inches Inside diameter: 0.57 inches Width: 0.16 in...

OEM #: 12023 This rubber magneto base plate seal has a steel outer shell. Measurements: Outside diameter: 1.032 inches Inside diameter: 0.700 inche...

OEM #: 29560-55 Magneto coil contact springs fit Fairbanks Morse and most after market units. Fitment: 1958-1969 XLCH

Eastern #: A-27291-32 · OEM #: 27291-32, 1247-32 Linkert carburetor throttle shaft springs. Fitment: 1936-1940 EL 1941-1965 FL 1937-1948 UL ...

Inner bearing race for Joe Hunt Morris Fairbanks Morse magnetos. Race for points plate bearings OEM # 29562-55 for rotor cam end. Notes:Suggested t...

OEM #: 29621-55T Rotor shaft end snap ring. Measurements:Outer Diameter: 36.80mm Fitment: 1958-1962 XLCH

OEM #: 29562-55, 29563-55 Magneto bearing set includes upper and lower bearings lower bearing washer and lower bearing seal. Set fits all Fairbanks...