Products

32 inch muffler set features a chrome 29 inch body and 3 inch black tapered end tips with a 4-1/2 inch outer diameter. Order replacement T-bolts se...

Barnett #: 101-30-40021 · OEM #: 56401-96 Barnett black vinyl idle cable is stock length. Casing is 32.50 inch and overall length is 37.50 inch. Fi...

32E 12 volt alternator gear kit is used to install alternators with 1/4 inch mount screws. Kit includes generator strap. Replaces 1936-1957 3 brush...

Volt Tech #: 18408 Generator bearing housing kit is for ends on 3-brush 32E generators. This kit features the front and rear bearings shim housing ...

Volt Tech #: 0150500 · OEM #: 30132-32, 1505-32 Aluminum generator left frame end housing is for 6 volt 3 brush 32E generators. Notes: Suggested to...

32E generator mount gasket set is for use with 6 volt 3 brush generators. Sold as a set of 2. Fitment: 1936-1952 EL 1941-1957 FL

Generator parts kit for 3 brush generators includes brush set terminals gaskets and a brass tag. Fitment: 1936-1952 EL 1941-1952 FL 1936-1952 W

Barnett #: 101-31-40011 Barnett black idle cable is 33 inch in length for S&S Super inchE inch and inchG inch carburetors. Measurements:Casing:...

33 inch Bronx straight tail set features a chrome finish and an inner diameter of 1-5/8 inch and comes without baffles. Bronx tail pipe extension f...

inch1 city handlebar features a chrome finish. Measurements: Rise to Grip Tip: 3-1/4 inches Rise to Center: 3 inches Pull Back: 8 inches Width Tip ...

Chrome round stock sissy bar. Use on Captain America replicas. Made for rigid frames only with 4 or 6 inch flat or ribbed fender. Measurements: Bot...

Black throttle and idle cable set with 90° elbow fitting. These cables are 33-1/2 inch long. The overall length including travel measures 38-1/2 in...

Barnett #: 101-30-30012 · OEM #: 56343-01 Barnett black vinyl throttle cable has a 33.25 inch casing length and an overall length of 38.37 inch. Ca...

Eastern #: A-45818-SET · OEM #: 45818-52 Fork bushing set is 33.4mm. Sold as a set of four. *NOTE: These will need to be sized to the fork tubes. T...

Damper kit with steel legs includes damper tubes with rings screws washers lower stops slider seal washers and retaining rings for both sides. Orde...

Hard chrome fork tube and piston assembly includes top plugs plungers and fork tubes that are fitted to 33.4mm. Fitment: 1957-1971 XL

Eastern #: 2-824 · OEM #: 46057-71 Fork spring set features high tensile strength wire construc tion with ground ends. Measurements:Length: 19-13/1...

OEM #: 46052-52 This 33.4mm fork tube spring set features high tensile stren gth wire construction with squared and ground ends. Measurements:Lengt...

Barnett #: 101-30-30014 · OEM #: 56343-90 Black throttle cable with 90° elbow fitting. This cable has a casing length of 33.50 inch. Fitment: 1990...

OEM #: 56564-02 Throttle and idle set in braided stainless steel with clear coat is stock length. Casing lenggth is 33.66 inch. Stainless steel bra...

OEM #: 45975-71 33mm fork seal set comes as a set of 5. Fitment: 1971-1972 FX 1971-1972 XL

Eastern #: A-11048 · OEM #: 11048 39mm snap ring for fork sliders. Fitment: 1971-1972 FX 1952-1956 K 1957-1972 XL

OEM #: 46001-71 Black rubber fork boot 33mm is designed for a better fit and improved sealing and wiping action. Sold in a quanity of 2. Fitment: ...

OEM #: 67079-86A Black front wheel drive speedometer cable with 12mm top nut. This cable has a length of 34 inch. Measurements: Casing Length: 34 i...